VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit supplier scorecard walkthrough
starter vape kits · adult smokers

Starter Vape Kit supplier scorecard walkthrough

Starter Vape Kit is a specification decision before it is a price decision. Get the resistance, the capacity and the packaging right and the price conversation becomes short. Get them wrong and no discount will rescue the order.

Published 02 April 2026  ·  VapeWholesaleHub  ·  Reading time 5 min

Bulk packing station during the run for a adult smokers order.
Bulk packing station during the run for a adult smokers order.
Packaging proof for the export market, approved before the run.
Packaging proof for the export market, approved before the run.

The checks behind every shipment

Buyers come to us for starter vape kit after a bad quarter: dead stock on one side, empty shelves on the other. The cause is usually the same, an assortment built from a catalogue instead of from sell-through data. This page explains how we rebuild that balance for adult smokers.

Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.

Battery safety is not a marketing line. Cells are matched by capacity and internal resistance before assembly, charging boards are checked for cut-off voltage, and any unit that fails the cut-off test never reaches packing.

Getting the documents right

If you sell into a market that requires child-resistant packaging, say so at quotation stage. Retrofitting a CR closure onto a finished bottle design usually means a new mould and a four week delay.

Advertising rules are stricter than product rules in most markets. Claims about cessation, health or comparative performance should stay off packaging and off your product pages unless your legal team has signed them off.

For adult smokers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

How orders move from factory to shelf

We ship from Shenzhen and Guangzhou: air express for samples and part loads, sea freight for volume. Typical production lead time is 12 working days after artwork approval, plus transit. We quote both routes so you can see the trade-off instead of guessing at it.

For repeat buyers we hold a shipping schedule rather than shipping on request. A fixed weekly cut-off means your reorder lands before the shelf empties instead of after.

  • Named account contact who has handled the product
  • Mixed SKU cartons to spread first-order risk
  • Reference sample retained from every batch
  • Document pack prepared per destination market
  • Consolidated or split shipping, quoted both ways
  • Seven-day defect reporting with replace-or-credit

Presentation that earns the step-up

Bundle a device with a consumable and the reorder rhythm changes from occasional to weekly. That single merchandising decision often does more for monthly revenue than a price promotion.

Staff knowledge converts better than any poster. If your team can explain the difference between two coils in one sentence, the step-up SKU sells itself.

Specification summary

Typical specification for this category
Battery500 mAh
Pod capacity2.5 ml
Coil resistance1.0 ohm
IncludedDevice, pod, cable
ChargingUSB-C 5V/1A
PackagingRetail box
Minimum order300 units per SKU, mixed cartons allowed
Lead time30 working days after artwork approval

None of this is complicated. It is just written down, which is more than most buyers get before they wire a deposit.

Frequently asked

How long does production take?

Around 12 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

How do you handle repeat orders?

The specification is held on file against your account, so a reorder is a reference rather than a new brief. We recommend a standing schedule with a fixed weekly cut-off so stock lands before the shelf empties.

What is the minimum order for starter vape kit?

Standard configurations start at 50 units per SKU, with mixed SKUs allowed inside the same carton. Custom colours, custom packaging or a private label run usually start at 200 units because of setup time on the line.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us